Just use another parameters, like point size, to encode that third variable as we can see in the second figure below.
All of these points we just discussed also line right up with the first chart.
Scatter plot with colour groupingsScatter plot with colour groupings and size encoding for the third variable of country sizeNow for the code.
We first import Matplotlib’s pyplot with the alias “plt”.
To create a new plot figure we call plt.
subplots() .
We pass the x-axis and y-axis data to the function and then pass those to ax.
scatter() to plot the scatter plot.
We can also set the point size, point color, and alpha transparency.
You can even set the y-axis to have a logarithmic scale.
The title and axis labels are then set specifically for the figure.
That’s an easy to use function that creates a scatter plot end to end!Line PlotsLine plots are best used when you can clearly see that one variable varies greatly with another i.
e they have a high covariance.
Lets take a look at the figure below to illustrate.
We can clearly see that there is a large amount of variation in the percentages over time for all majors.
Plotting these with a scatter plot would be extremely cluttered and quite messy, making it hard to really understand and see what’s going on.
Line plots are perfect for this situation because they basically give us a quick summary of the covariance of the two variables (percentage and time).
Again, we can also use grouping by colour encoding.
Line charts fall into the “over-time” category from our first chart.
Example line plotHere’s the code for the line plot.
It’s quite similar to the scatter above.
with just some minor variations in variables.
HistogramsHistograms are useful for viewing (or really discovering)the distribution of data points.
Check out the histogram below where we plot the frequency vs IQ histogram.
We can clearly see the concentration towards the center and what the median is.
We can also see that it follows a Gaussian distribution.
Using the bars (rather than scatter points, for example) really gives us a clearly visualization of the relative difference between the frequency of each bin.
The use of bins (discretization) really helps us see the “bigger picture” where as if we use all of the data points without discrete bins, there would probably be a lot of noise in the visualization, making it hard to see what is really going on.
Histogram exampleThe code for the histogram in Matplotlib is shown below.
There are two parameters to take note of.
Firstly, the n_bins parameters controls how many discrete bins we want for our histogram.
More bins will give us finer information but may also introduce noise and take us away from the bigger picture; on the other hand, less bins gives us a more “birds eye view” and a bigger picture of what’s going on without the finer details.
Secondly, the cumulative parameter is a boolean which allows us to select whether our histogram is cumulative or not.
This is basically selecting either the Probability Density Function (PDF) or the Cumulative Density Function (CDF).
Imagine we want to compare the distribution of two variables in our data.
One might think that you’d have to make two separate histograms and put them side-by-side to compare them.
But, there’s actually a better way: we can overlay the histograms with varying transparency.
Check out the figure below.
The Uniform distribution is set to have a transparency of 0.
5 so that we can see what’s behind it.
This allows use to directly view the two distributions on the same figure.
Overlaid HistogramThere are a few things to set up in code for the overlaid histograms.
First, we set the horizontal range to accommodate both variable distributions.
According to this range and the desired number of bins we can actually computer the width of each bin.
Finally, we plot the two histograms on the same plot, with one of them being slightly more transparent.
Bar PlotsBar plots are most effective when you are trying to visualize categorical data that has few (probably < 10) categories.
If we have too many categories then the bars will be very cluttered in the figure and hard to understand.
They’re nice for categorical data because you can easily see the difference between the categories based on the size of the bar (i.
e magnitude); categories are also easily divided and colour coded too.
There are 3 different types of bar plots we’re going to look at: regular, grouped, and stacked.
Check out the code below the figures as we go along.
The regular barplot is in the first figure below.
In the barplot() function, x_data represents the tickers on the x-axis and y_data represents the bar height on the y-axis.
The error bar is an extra line centered on each bar that can be drawn to show the standard deviation.
Grouped bar plots allow us to compare multiple categorical variables.
Check out the second bar plot below.
The first variable we are comparing is how the scores vary by group (groups G1, G2, .
etc).
We are also comparing the genders themselves with the colour codes.
Taking a look at the code, the y_data_list variable is now actually a list of lists, where each sublist represents a different group.
We then loop through each group, and for each group we draw the bar for each tick on the x-axis; each group is also colour coded.
Stacked bar plots are great for visualizing the categorical make-up of different variables.
In the stacked bar plot figure below we are comparing the server load from day-to-day.
With the colour coded stacks, we can easily see and understand which servers are worked the most on each day and how the loads compare to the other servers on all days.
The code for this follows the same style as the grouped bar plot.
We loop through each group, except this time we draw the new bars on top of the old ones rather than beside them.
Regular Bar PlotGrouped Bar PlotStacked Bar PlotBox PlotsWe previously looked at histograms which were great for visualizing the distribution of variables.
But what if we need more information than that?.Perhaps we want a clearer view of the standard deviation?.Perhaps the median is quite different from the mean and thus we have many outliers?.What if there is so skew and many of the values are concentrated to one side?That’s where boxplots come in.
Box plots give us all of the information above.
The bottom and top of the solid-lined box are always the first and third quartiles (i.
e 25% and 75% of the data), and the band inside the box is always the second quartile (the median).
The whiskers (i.
e the dashed lines with the bars on the end) extend from the box to show the range of the data.
Since the box plot is drawn for each group/variable it’s quite easy to set up.
The x_data is a list of the groups/variables.
The Matplotlib function boxplot() makes a box plot for each column of the y_data or each vector in sequence y_data; thus each value in x_data corresponds to a column/vector in y_data.
All we have to set then are the aesthetics of the plot.
Box plot exampleBox plot codeConclusionThere are your 5 quick and easy data visualizations using Matplotlib.
Abstracting things into functions always makes your code easier to read and use!.I hope you enjoyed this post and learned something new and useful.
Like to learn?Follow me on twitter where I post all about the latest and greatest AI, Technology, and Science!.Connect with me on LinkedIn too!.